Repair samsung p3100 Remove Write Protection by Easy Jtag

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:453 mV
CMD Active Level:752 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:907 mV
CMD Active Level:1165 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 1501004D414732474107E1103DDA4FCE

EMMC CSD : D02701320F5903FFF6DBFFFF8A406062

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2012 Rev.0x7
EMMC NAME: MAG2GA , S/N: 3775938010
EMMC NAME (HEX): 4D414732474100
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: Yes
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x03

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

---------------------------------------------

Backup saved: MAG2GA_3775938010_20161224_1019.extcsd
Done.

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:907 mV
CMD Active Level:1165 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 1501004D414732474107E1103DDA4FCE

EMMC CSD : D02701320F5903FFF6DBFFFF8A406062

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2012 Rev.0x7
EMMC NAME: MAG2GA , S/N: 3775938010
EMMC NAME (HEX): 4D414732474100
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: Yes
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x03

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

---------------------------------------------

Backup saved: MAG2GA_3775938010_20161224_1019.extcsd
Done.

Running:SAMSUNG: Remove Write Protection...
Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:907 mV
CMD Active Level:1165 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
Removing write protection...
Done.

Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:907 mV
CMD Active Level:1165 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
Reading 0x000002000000 bytes from 0x000000000000 ...ROM1 ( USER ROM)
Output file :D:\JTAG\EasyJTAG\Samsung\P3100\EMMC_ROM1_MAG2GA_3775938010_00000000_02000000.bin
Done. Read Speed: 1393 kB/s

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N:CCXXXXXXXXXXX 8, ,FW Ver.: 01.56
Warning: CMD Pullup Level (897 mV) too low , check cables etc.!
CMD Active Level:1165 mV
Box IO Level:3300 mV
CLK Rate:140000 khz
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Success!
eMMC firmware is updated now! 
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:907 mV
CMD Active Level:1134 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 1501004D414732474105C8049C3A5F36

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0x5
EMMC NAME: MAG2GA , S/N: 3355745338
EMMC NAME (HEX): 4D414732474100
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x03

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

---------------------------------------------

Backup saved: MAG2GA_3355745338_20161224_1021.extcsd
Done.

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:907 mV
CMD Active Level:1155 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x03

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

---------------------------------------------

Backup saved: 000000_ 537986854_20161224_1022.extcsd
Done.

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXXXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:907 mV
CMD Active Level:1165 mV
Box IO Level:3300 mV
CLK Rate:140000 khz
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now! 
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXXXXXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:907 mV
CMD Active Level:1124 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 1501004D41473247300720129C3A5FAE

EMMC CSD : D02701320F5903FFF6DBFFFF8A404006

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0x7
EMMC NAME: MAG2G0 , S/N: 538090554
EMMC NAME (HEX): 4D414732473000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x03

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

---------------------------------------------

Backup saved: MAG2G0_ 538090554_20161224_1023.extcsd
Done.

Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:907 mV
CMD Active Level:1124 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
Writing...
Done.

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XXXXXXXXXXXXX, ,FW Ver.: 01.56
CMD Pullup Level:897 mV
CMD Active Level:1165 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 1501004D41473247300720129C3A5FAE

EMMC CSD : D02701320F5903FFF6DBFFFF8A404006

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0x7
EMMC NAME: MAG2G0 , S/N: 538090554
EMMC NAME (HEX): 4D414732473000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x03

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

---------------------------------------------

Backup saved: MAG2G0_ 538090554_20161224_1024.extcsd
Done.

Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:897 mV
CMD Active Level:1165 mV
Input file : D:\JTAG\EasyJTAG\Samsung\P3100\Dump\DL\P3100 USERAREA\P3100 USERAREA.bin
Writing 0010000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 1990 kB/s

Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:897 mV
CMD Active Level:1165 mV
Input file : D:\JTAG\EasyJTAG\Samsung\P3100\Dump\DL\P3100 BOOT1\P3100 BOOT1.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 1168 kB/s

Z3X EasyJtag Software ver. 2.4.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:897 mV
CMD Active Level:1165 mV
Input file : D:\JTAG\EasyJTAG\Samsung\P3100\Dump\DL\P3100 BOOT2\P3100 BOOT2.bin
Writing 0000200000 bytes to 00000000 ...ROM3 (BOOT2 ROM)
Done. Write Speed: 1371 kB/s

Writing 0001400000 bytes to 00400000 ...ROM1 (USER ROM)
Done. Write Speed: 324 kB/s

admin Selasa, 10 Januari 2017 Easy JTAG repair Emmc

Repair samsung p3100 Remove Write Protection by Easy Jtag

0 Response to Repair samsung p3100 Remove Write Protection by Easy Jtag

Posting Komentar